Friday, October 02, 2009

Items For Sale

I have a few items for sale. All items are in excellent condition and have done very low mileage!

1. Matspeed 3R 292 (inlet) and 288 (exhaust) spec camshafts - RM1,600.00


2. Matspeed J5 ECU to suit above cam and high compression ratio engine, rev limit at 9000 rpm - RM750.00

3. NGK Hyper Silicone Power cables - RM 220.00

4. Exedy Clutch Cover and Organic Plate, still a lot of material on the plate left - RM 450.00

5. 4G93T inlet manifold fully ported - RM 350.00

6. 60mm throttle body fully ported - RM 350.00

7. Power Enterprise Super Strong Timing Belt, done about 20k km only - RM 300.00

8. Stock 4G93P inlet manifold, like new - RM 150.00

9. Brand new 4G9x SOHC oil pump (front case assembly) - RM 500.00

10. One unit MAF sensor with standard rubber hose and Hot Bits adaptor plate for K&N cone air filter. MAF Sensor Code 455 - RM200.00

11. Two brand new Nokia E71, ori set just out of the box, full warranty - RM1100.00 each

Send me a message if any of the above is of interest, meanwhile I will try to take some pictures and upload it here.

Monday, August 03, 2009

Rebuild - Part 4

Purchased a new seat for the SP as well, only driver side currently, Recaro SP-G Carbon Kevlar. Bought a used one which was going for a very good price and in very good condition. Pictures below

It is quite light and feels good to sit on, not sure about how well it will fare on longer journeys, especially since I have gained more weight!! Hoping to get another one to complement the passenger seat and a lightweight 4 point harness to go with it. Sabelt here I come!!
Here is quite a recent picture of SP outside the workshop. Notice anything different, besides the different color bonnet of course? Sorry picture quality aint that good as it was taken from my mobile phone.


And a sneak peek of whats coming up, was mocking things up for my new airbox.
Till next time!

Monday, July 13, 2009

Rebuild - Part 3

Sorry been quite busy with work and travels.
Well the engine is now off SP. As suspected the previous engine officially died due to loss of bearing on con rod no 4. Didnt take any pictures, so couldnt show the extent of the damage.

Got my pistons and rods, all forged. The new engine will feature, head studs, main bolts and rod bolts all from ARP. I will be running a different induction system now, details which I do not want to reveal now, but some will be familiar with JD.



Hopefully SP can be ready in a month or two's time as it has been out of action since last year November, so I am very keen to drive it again. The build is going on slow, but usually its worth the wait for good things to happen, so I hope!

Got more Ti bolts too, currently for all the oil sump bolts and camber adjustment plates (pillow ball mount) on my Ohlins. Set me back more then Rm500 just for these!! Got more bolts planned, but these will be custom made in Grade 5 Ti to lighten SP further.

I am intending to get my oil sump baffled, but not sure who is able to do it locally? Any suggestions?
Hopefully more pictures next time!

Sunday, March 01, 2009

Rebuild - Part 2

Got my pistons ordered at last, hopefully it will be here in 4-5 weeks time. Going for Wiseco with 11.5:1 comp ratio, 82mm diameter. Getting the piston skirt and crown ceramic coated as well. Its funny Wiseco does not like to deal with customers outside of USA, maybe too much hassle. So got my friend in the US to do all the communicating and ordering. They are not cheap as its apparently custom made. I just hope all fits well without any snag!!

This is also a important as now the bottom end build can begin, as soon as the piston arrives. Its been 3 months now since I have driven SP. Its sad watching it on the driveway covered and without getting any action.

This is another item which I have just ordered :

"The revolutionary new KS-4 is our most advanced knock detection system. Offering all the great functionality of the KS-3 but also a fully configurable 0-5v outputand a remote alarm function allows the KS-4 to trigger a remote warning system." more details here http://www.phormula.co.uk/KnockMonitor-KS-4.aspx

This will help when tuning the SP and also on track days, just in case something goes wrong, at least I will get a warning instead of risking damage on the engine. Not sure how I am going to go about doing this but when it detects a knock signal it will give out a 0-5V output which I intend to use to activate the water injection kit. More of that in the next post.


Sunday, February 15, 2009

Rebuild - Part 1

Figured that I would just make a quick update on the progress has its been a while since I last updated the blog. Car is still sitting at home and nothing has been done still...as I am still waiting for my pistons. Hope that I am able to receive it in about 6 weeks time and thereafter commence the bottom end rebuild. Starting from a fresh block as the current one is already at its max bore, unless I sleeve it. Also since I will be doing full rebuild, thought I might as well change my clutch, although the current Exedy with organic plate one is still pretty good. This is because I am getting the entire rotating assembly dynamically balanced and do not want to disturb the balance when I change clutch. So hopefully a new clutch will eliminate this issue for a while. Getting the same clutch again as its grip is pretty good and doesnt judder during takeoff...also that it lasted 4 track days...

Also thinking of changing to the Mythelogy LCP with the rubber damper, as Fluidamper do not make one for the 4G93 engines. For EVO engine they have got some models...other than that dont have.

Also received my water injection kit, thats something else that needs to be hooked up along with a few other accessory. I am going a bit mad this time, and also have purchased a 6 point Safety21 roll cage, which I probably install after the rebuild is done.

Will update more when time permits....

Sunday, December 07, 2008

Rebuild

During HPC last week, I think I have spun a con rod bearing or damaged the bearings somehow. Mid way through the last session, the car started to make funny noises which I could not really hear with the helmet on. Drove into the pits, took off the helmet and my fears were confirmed, as I was hoping it was something else. Car is back in my place while I gather some parts for a rebuild. I will only know what really happend when the engine is stripped.
Hoping to rebuild it with slightly different parts and make slightly more power than before. The engine just before giving in made about 170+ whp with about 18kg of torque, which is not bad for the 4G93P without any Mivec or Turbo, and running on pump gas.
Lets see how it goes!!! Watch this space!

Thursday, September 18, 2008

HPC 30th November 2008

May not come as a suprise but I have now registered for a place in Gp 2 for the HPC event on the 30th November. It will be a full track event so I need to work on SP to increase more front end grip especially through T5 and T6 based on the previous track day experience. Plan to get SP corner weight'ed before the event, lets see whether I can fit that in my tight work and life schedule. FYI I have only clocked less than 5k km on the SP since purchasing it which is going to be about 2 years now.

Anyone else going for the HPC event on 30th Nov? Do drop a line as it will be nice to put a face to the name/nick on that day!



ARP Head Stud Kit

This is an important upgrade especially if you are running high compression or high boosting engines as to prevent head stretch.

Some information on the ARP studs :

"Obtaining the optimum cylinder head-to-block sealing is especially critical in small displacement engines employing high compression pistons or power adders like turbochargers, nitrous oxide and superchargers. That's why ARP® head studs are popular among leading Sport Compact/Import racers.

You should know that ARP® uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Then, each stud is precisely heat-treated to 200,000 psi. Following heattreat, each stud is centerless ground to make it as close to perfectly concentric as possible. This procedure involves about ten very slight cuts and results in an exceptionally straight part. It's important to note that lesser quality studs are not even centerless ground—the material is thread rolled in bar stock form (mostly before heat-treat, when the material is easier to machine). Because ARP® studs are manufactured to such exacting tolerances, you will note that gaskets and cylinder heads literally glide into position and are perfectly aligned—something that won't happen with inferior quality head studs.

ARP® studs are thread rolled after heat-treat, which gives them about 1000% (that's ten times) better fatigue strength than those studs that are threaded prior to heat-treat.

You will also note that ARP® offers specially undercut studs for several engines. This procedure (done only to the shorter studs) more equalizes the "stretch" of both studs, which makes for a more consistent clamping force—one that compensates for head gasket compression when the head is installed. This helps prevent blown head gaskets, and assures optimum sealing!

Premium parallel ground washers are also included with each kit." Article from ARP website.


I bought this kit from RPW directly when I was in Perth. RPW are famous in Australia for the performance modifications on Mistsubishi's especially the older models. It was not cheap at AUD 295.00 for the head stud kit alone!

Some pictures:







The kit come with the stud, bolts, thick flat washers , ARP molybdenum assembly lube, installation guide (torque settings) and ARP sticker. ARP provides their own default torque values which is much higher than the manufacturers recommendation. This provides better sealing between the head and the gasket and ultimately much better reliability.

Monday, August 11, 2008

HPC 20th April 08

This should have been blogged sometime ago but I have been quite busy. This was my first time on the SIC track and my first HPC event. I registered for the Gp 2 morning session along with a few other friends - Khai in his x-147 2.0 Selespeed, Ken - x-AE86, CP - in his Satria 1.6 Turbo, Jack - SGTI 1.8 Turbo and Senior - SGTI 2.0 Turbo. My wife also decided to come and support me for the day.

The day before the event, I got the car aligned and the camber set to -2 degrees on the front and -1 deg at the rear. Also filled up the tyres with Nitrogen and set it to 32psi on all fours. Set the Ohlins to the recommended track setting and removed the rear seats for further weight savings! On the engine front the car was not in its ideal condition as I had a head gasket leak which at high revs causes some oil and coolant (only realized this at the track) to leak. So best to be cautious and I imposed a self rev limit of 7.5k rpm.

Jack's day started with a intercooler hose coming off just before arriving at the track. This was quickly fixed and all of us got into fixing the stickers which were provided. In Group 2 I think there were about 30 cars, RX7, RX8's, Impreza's, Satria Neo, Civics, old skool Saab and a few others. Feeling all jittery about the track and the car, I was taking it easy for the first few laps just to familiarize with the track and SP. After getting comfortable I started to push on and started to push the car more by braking later and trying different lines on the turns. So much so that at one point got too excited with my braking points and overcooked turn 9 while Sr was in the outside line and I was heading straight on to a RX7 which was halfway into the turn. Luckily I was able to keep things in check (thank you God!) and managed to avoid any incidents. I pulled in early to check the conditions under the hood and during that time was told off by the marshall that I cannot perform late braking and overtake on turn 9. Oh well, only if he really knew what happened.

Anyway it was a great outing for me and the SP and the car handled brilliantly on the track although it was smoking quite a lot, esp when I heel n toe into a turn, SP was emitting big clouds of white smoke from the exhaust. After the track day a top overhaul was required as the head gasket was on the way out and as well as the valve guides and a few other items which needed replacing. Jacko ended the day with a lil problem as well as his main relay gave way and was not able to start the car. Luckily his mechanic was there to watch the event and was able to make a quick fix. Well I will let the pictures do the talking.
Getting ready to go on the track. No more CF bonnet..sob sob!
Lining up at the pits

CP's Gangster Green Slutria

Jack and his playstation, the SGTi of course!!


Cooling down after the first session - corner markers on the tyres were full before first session, now totally gone!

Khai's 147 Selespeed! Now replaced with a different turbocharged monster!

Seniors freaking fast GTi

My reminder!


Blasting through the straights

Another shot different angle

Me, wifey and SP after the track day!

Saturday, August 02, 2008

V Sixers Track Day 30th July

I was trying very hard to get myself registered for the trackday event organized by Vsixers through the SGTI club. After a couple of weeks of trying and my itch to have a go at the full track becoming more intense, I decided to just go to SIC and try my luck. The gods of track days must have been shining on me as I managed to get SP in for the event. Also thanks to Jack who was helping me out all the while!
There were about 30 Perdana V6, 8 Satria GTi, 5 Savvy, 15 Neo's and 1 Putra all ready in the pits raring to go. My first session on the full track was a bit boring, I didnt feel right, the car wasnt feeling right too and not too long into the first session I had my first spin in the SP on turn 10 which happens to be one of my favourites since HPC track day. I also attribute this to my own mistake as the day before the event I decided to swap the tires from rear to front and vice versa, which left me with tyres with more tread on the front and lesser treads at the rear. This in turn reduced the grip on the rear which made it more oversteery! I kinda "woke up" after the spin and decided to head to the pits to calm down a little. Checked tire pressure and dropped the front a little and the car felt much better on the next sessions.
The car felt a touch oversteery on turns 5 & 6 which are the high speed left and right and reckon some aerodynamic aid to get more downforce will be beneficial. The brakes performed well and the only trouble I had was a loose dipstick. This made me to loose some oil and dirty the engine bay. Managed to get some duct tape from one of the SGTI members (thanks man!) and did a quick fix to the dipstick.
It was good experience for me and to learn SP's handling limits in a safe environment. I still have a lot to learn in terms of being more smooth and consistent with my lines, braking points and turning points as its my first time being out on the full track. Nevertheless the day did have some incidents like a Satria Neo crashing into a wall and Jack's car stuck at the pit entrance which resulted in red flags being shown. We had to wait for about 10 mins before the track was OK to be used again.
Oh on the way home there was a rattling sound coming from the rear which I thought was due to a broken suspension/arb link but found out that bolts holding the rear boot hinge has managed to work out loose due to all the shenanigans of driving in the track!
Sorry no pictures!